NTC1512638S Voltronic GXT-3000MTPLUS230
UPS(IEC+澳洲偏差)LVD Report
(2)_甜梦文库
NTC1512638S Voltronic GXT-3000MTPLUS230
UPS(IEC+澳洲偏差)LVD Report
Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638STEST REPORTApplicant Address Manufacturer Address Product Name Trade Mark : : : : : : Emerson Network Power Australia Pty Limited 15 Talavera Rd, Level 6, Suite A, North Ryde, NSW, Australia 2113 Emerson Network Power Australia Pty Limited 15 Talavera Rd, Level 6, Suite A, North Ryde, NSW, Australia 2113 UPSModel No. Ratings: :GXT-3000MTPLUS230 Input: 208Vac-240Vac, 50/60Hz, 14.4A, 1Φ Output: 208Vac-240Vac, 50/60Hz, 1Φ Capacity: 3000VA/2400WStandard:Uninterruptible power systems(UPS) Part 1: General and safety requirements for UPS IEC 08+A1:2013 Australia deviationDate of Receiver Date of Test Date of Issue Test Report Form No Test Result: : : : :December 26, 2015 December 26, 2015 to December 30, 2015 December 31, 2015 NTCS-IEC-APass *Approved byThis Test Report is Issued Under the Authority of : Compiled byVicky / EngineerHan Song / Manager*Remarks: The results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of Dongguan Nore Testing Center Co., Ltd. The report would be invalid without specific stamp of test institute and the signatures of compiler and approver.TEL: +86-769- FAX: +86-769- Web: www.ntc-c.com Address: Building D, Gaosheng Science & Technology Park, Zhouxi Longxi Road, Nancheng District, Dongguan City, Guangdong, ChinaPage 1 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SRevision History of This Test ReportReport Number NTC1512638S Description Initial Issue Issued Date Page 2 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SCopy of marking plate:Note: The trade markmarked on other position of the enclosure surface.Summary of testing: The submitted samples were found to comply with the above standard. ? Tests performed on the bench ? Maximum ambient temperature: +40°C ? Tested for moderate conditions ? Evaluation for use on elevations not exceeding 1000m (see Note of subclause 1.2)Page 3 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638STest item particulars ................................... : Equipment mobility ...................................... : movable hand-held transportable stationary for building-in direct plugin pluggable equipment type A type B permanent connection detachable power supply cord non-detachable power supply cord not directly connected to the mains continuous rated operating / resting time: operator accessible restricted access location OVC I OVC II OVC III OVC IV other: -10% to 6% (requested by client) Yes (only for Norway) N/A Class I Class II Not classified 16A PD 1 PD 2 IP20 Up to 1000m below 1000m 28kg N P (Pass) F (Fail) PD 3 No Class IIIConnection to the mains ............................. :Operating condition ..................................... : Access location .......................................... : Over voltage category (OVC) ..................... :Mains supply tolerance (%) or absolute mains supply values ................................... : Tested for IT power systems ...................... : IT testing, phase-phase voltage (V) ........... : Class of equipment .................................... : Considered current rating of protective device as part of the building installlation (A) .................................................................... : Pollution degree (PD) ................................. : IP protection class ...................................... : Altitude during operation (m) ...................... : Altitude of test laboratory (m) ..................... : Mass of equipment (kg) ............................. : Possible test case verdicts: - test case does not apply to the test object . : - test object does meet the requirement ....... : - test object does not meet the requirement . : General remarks:Page 4 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638S&(see Enclosure #)& refers to additional information appended to the report. &(see appended table)& refers to a table appended to the report. Throughout this report a comma is used as the decimal separator. Standard IEC 8 is to be used in conjunction with IEC 5, which is referred to in this TRF by “RD”. General product information: The model of Uninterruptible Power Supply included in this test report. The equipment were general designed for using with information technology equipment. Double/reinforced insulation provided between primary circuits and SELV circuits by safety isolation transformer and sufficient clearances and creepage distances within the unit. Appliance shall be provided with an approved power supply cord with plug complying with the national regulations of the countries in which the appliance is to be sold.Page 5 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark Verdict4 4.5GENERAL CONDITIONS FOR TESTS Components Comply with IEC 62040-1 or relevant component standard Components, which were found to affect safety aspects, comply with the requirements of this standard or within the safety aspects of the relevant IEC component standards. (see appended table 4.5) Components, which are certified to IEC and/or national standards, are applied correctly within their ratings. Components not covered by IEC standards are tested under the conditions present in the equipment. Transformers used are suitable for their intended application and comply with the relevant requirements of the standard. The interconnecting cable is carrying only SELV voltage on a low energy level. X2 capacitors provided between lines, and Y2 capacitors provided between line and earth. See below. Bleeder resistors bridging functional insulation. No such resistors used.P P P1.5.2/RD Evaluation and testing of componentsP1.5.3/RD Thermal controls 1.5.4/RD TransformersN P1.5.5/RD Interconnecting cablesP1.5.6/RD Capacitors bridging insulationP1.5.7/RD Resistors bridging insulation 1.5.7.1/R Resistors bridging functional, basic or supplementary insulation D 1.5.7.2/R Resistors bridging double or reinforced insulation between a.c. mains and other D circuitsP P NPage 6 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark VerdictNo such resistors used. 1.5.7.3/R Resistors bridging double or reinforced insulation between a.c. mains and antenna D or coaxial cable 1.5.8/RD Components in equipment for IT power systems 4.6 Power interface For connection to TN power system. (see appended table 4.6) Neutral conductor is basic insulated from earth and body of the equipment.NNP P P P1.6.1/RD AC power distribution systems 1.6.2/RD Input current 4.6 Neutral conductor 1.6.4/RD4.7 4.7.1Marking and instructions General Required marking was located on the outside of the equipment. See the copy of marking plate See the copy of marking plate See the copy of marking plate AC input See the copy of marking plate 1φ with neutral See the copy of marking plateP P4.7.2 Power rating 1.7.1/RD Input rated voltage/range (V) ...............: Input rated current/range (A) ...............: Input symbol for nature of supply (d.c.) : Input rated frequency/range (Hz) .........: Number of Input phases and neutral ...: Output rated voltage/range (V) ...........: Output rated current/range (A) ............:P P P N P P P N PSee the copy of marking Output rated power factor, if less than unity, or active power and apparent power plate or active power and rated current .......: Number of output phases and neutral : 1φ with neutralPPage 7 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark VerdictOutput rated active power (W or kW) .: Output rated apparent power (VA or kVA) ............................................................: Output symbol for nature of supply (d.c.) ............................................................: Output rated frequency/range (Hz) ......:See the copy of marking plate See the copy of marking plate AC output See the copy of marking plateP P N P P NAmbient operating temperature range (?C) 0-40?C ............................................................: Rated short-time withstand current (Icw) or rated conditional short-circuit current (Icc) Manufacturer?s name or trademark or identification mark ...............................: Type/model or type reference ..............: Symbol for Class II equipment only ....: Other symbols ....................................: See the copy of marking plate See the copy of marking plate Class I equipment Additional symbols or marking do not give rise to misunderstanding.P P N PCertification marks ..............................:INSTRUCTIONS FOR UNITS WITH AUTOMATIC BYPASS/MAINTENANCE BYPASS, ADDITIONAL INPUT A.C. SUPPLY, OR EXTERNAL BATTERIES, HAVING TEXT &SEE INSTALLATION INSTRUCTIONS BEFORE CONNECTING TO THE SUPPLY& ............................................................ :P P4.7.3 4.7.3.1Safety instructions General The instruction contains information for operation, installation, servicing, transport, storage and technical data. Installation instructions are available to the user in User Manual.P P4.7.3.2Installation ........................................... :PLocation in a restricted access location only No a restricted access ............................................................ : location.NPage 8 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark VerdictPermanent connector UPS .................. :Not an permanent equipmentN P PPluggable type A or Pluggable type B UPS Pluggable type A UPS. ............................................................ : 4.7.3.3 Operation ............................................. : The equipment is intended to be operated by layperson. The instruction of maintenance is only included in the user manual. Not permanently connected equipment No voltage selector.4.7.3.4Maintenance ........................................ :P4.7.3.5Distribution related backfeed ............... :N N N4.7.4 Main voltage adjustment ..................... : 1.7.4/RD Methods and reference to installation instructions ... : 4.7.5 Power outlets ....................................... : 1.7.5/RDRelevant information provided on the marking that is affixed near the outletsP4.7.6 Fuse identification (marking, special fusing Marking required 1.7.6/RD characteristics, cross-reference) ......... : 4.7.7 Wiring terminals 1.7.7/RD 1.7.7.1/R Protective earthing and bonding terminals D ............................................................ : See below The earth terminal is marked with the standard earth symbol near the terminalP P P1.7.7.2/R Terminals for a.c. mains supply conductors Power plug used. ............................................................ : D 1.7.7.3/R Terminals for d.c. mains supply conductors Supply by AC source ............................................................ : D only. 4.7.8 Battery terminals ................................. : Internal battery used The marking “+” and “-” for indication of polarity of battery provided.N N PPage 9 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark Verdict4.7.9 Controls and indicators 1.7.8/RD 1.7.8.1/R Identification, location and marking .... : DSee below LCD provided to indicate the working condition, located on the front panel. A corresponding statement was provided in the User?s Manual. Colors are acceptable due to only used for information (no safety involved even if disregarded).P P1.7.8.2/R Colours ..............................................: DP1.7.8.3/R Symbols ..............................................: D 1.7.8.4/R Markings using figures .......................: D 4.7.10 Isolation of multiple power sources .....: 1.7.9/RD 4.7.11 IT power systems 1.7.2.4/R D 4.7.12 Protection in building installation Only one external supply of hazardous voltage of energy TN power distribution systems The protection does not rely upon building installation. The protection is provided by input breaker.P N NNNRated short-time withstand current (Icw) : Rated conditional short circuit current (Icc) ............................................................: a) If higher Icp stated ≤ 10 kA a) If higher Icp stated & 10 kA 4.7.13 5.1/RD High leakage current (mA) ..................: Leakage current of the equipment does not exceed 3.5mA.N N N N PPage 10 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark Verdict4.7.14 Thermostats and other regulating devices 1.7.10/R D 4.7.15 Language(s) .......................................: 1.7.2.1/R D and 1.7.8.1/R DNo thermostats and other regulating devices LCD provided to indicate the working condition, located on the front panel. A corresponding statement was provided in the User’s Manual. The marking withstands required tests No required markings placed on removable parts. Detailed instructions provided in the user?s manual. English. All areas containing hazard(s) are inaccessible to the operator. Pluggable equipment type A, UPS with integral batteries. Warning label attached on the outside surface of internal battery pack. Information clearly legible. Lead acid Stated on rating user?s manualNP4.7.16 Durability of markings 1.7.11/R D 4.7.17 Removable parts 1.7.12/R D 4.7.18 Replaceable batteries 1.7.13/R D Language(s) .......................................: 4.7.19 Operator access with a tool .................: 1.7.2.5/R D 4.7.20 BatteryPNP-NPClearly legible information ..................:PBattery type (lead-acid, NiCd, etc.) and number of blocks or cells .................... : Nominal voltage of total battery (V) .... :P P P PPage 11 of 73Nominal capacity of total battery (optional) Stated on rating user?s manual ............................................................ : Warning label ...................................... : ConsideredDongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark VerdictInstructions ......................................... :The sufficient information about the battery was given in the user?s manual. No energy hazard in operator access area. Detailed information regarding power distribution system, special attention to external interfaces.P2.1.1.5/R Protection against energy hazards D 4.7.21 Installation instructions 1.7.2.4/R DP P5 5.1FUNDAMENTAL DESIGN REQUIREMENTS Protection against electric shock and energy hazards See below. Checked by test finger and test pin. No accessible hazard energized parts. Not accessible Not accessible Not accessible No TNV circuits. No TNV circuits inside battery compartment. No ELV wiring in operator accessible area.P P P P5.1.1 Protection for UPS intended to be used in 2.1.1/RD operator access areas 2.1.1.1/R Access to energized parts DTest by inspection ............................... : Test with test finger (Figure 2A) .......... : Test with test pin (Figure 2B) .............. : Test with test probe (Figure 2C) ......... : 2.1.1.2/R Battery compartments D 2.1.1.3/R Access to ELV wiring D Working voltage (Vpeak or Vrms); minimum distance through insulation (mm) 2.1.1.4/R Access to hazardous voltage circuit wiring D 2.1.1.5/R Energy hazards .................................. : DP P P N P N --Insulation of internal wiring not operator accessible. No energy hazard at operator accessible SELV interfaces.NPPage 12 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark Verdict2.1.1.6/R Manual controls D 2.1.1.7/R Discharge of capacitors in equipment D Measured voltage (V); time-constant (s) . : 2.1.1.8/R Energy hazards C d.c. mains supply D a) Capacitor connected to the d.c. mains supply ...................................................... : b) Internal battery connected to the d.c. mains supply ....................................... : 2.1.1.9/R Audio amplifiers in information technology D equipment ........................................... : 5.1.2 Protection for UPS intended to be used in 2.1.1.5 c) service access areas /RD Hazardous energy level ...................... : 5.1.3 Protection for UPS intended to be used in 2.1.1.5 c) restricted access areas /RD Hazardous energy level ...................... : 5.1.4 Backfeed protection Shock hazard after de-energization of a.c. input for UPS Measured voltage (V); time-constant (s) . : Description of the construction ........... :No conductive controls or handles or alike provided. No risk of electric shock. (see appended table 2.1.1.7/RD) Not connected to DC mains supply.PP ? N N NNo audio amplifier Checked by inspection, unintentional contact is unlikely during service operations. Not for restricted access areaN NN NN (see appended table 5.1.4) See appended table 5.2.1 and Subclause 2.2.3/RD For pluggable UPS, backfeed protection achieved by the operation of relays and the relative circuits provided in the a.c. input line. P P-PPage 13 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark VerdictAir gap is employed for backfeed protectionThe relay provides a contact gap of 1.9 mm minimum between each contact. Pluggable equipment type A, no emergency switching device for the load required.P5.1.5Emergency switching (disconnect) deviceN5.2 5.2.1 2.2/RDRequirements for auxiliary circuits Safety extra low voltage circuit - SELV USB, RS232 and EPO port are considered as SELV circuit The secondary circuits were tested as SELV. Not exceed 42.4V peak or 60Vdc in SELV circuit under normal operation. (See appended table 5.2.1) Single fault cause did not excessive voltage in accessible SELV circuits. (See appended table 5.2.1) To SELV only No TNV circuitP P2.2.1/RD General requirements 2.2.2/RD Voltages under normal conditions (V) . :P P2.2.3/RD Voltages under fault conditions (V) ..... :P2.2.4/RD Connection of SELV circuits to other circuits ................................................ : 5.2.2 2.3/RD Telephone network voltage circuits - TNVN N N -N N N NPage 14 of 732.3.1/RD Limits Type of TNV circuits ............................ : 2.3.2/RD Separation of TNV circuits from other circuits and from accessible parts 2.3.2.1/R General requirements D 2.3.2.2/R Protection by basic insulation D 2.3.2.3/R Protection by earthing DDongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark Verdict2.3.2.4/R Protection by other constructions ....... : D 2.3.3/RD Separation from hazardous voltages Insulation employed ............................. : 2.3.4/RD Connection of TNV circuits to other circuits Insulation employed ............................. : 2.3.5/RD Test for operating voltages generated externally 5.2.3 2.4/RD Limited current circuits (See appended table 5.2.3) (See appended table 5.2.3)N N -N -N N N ? ? ? ? ? N P Considered. SELV circuits. No such ELV circuits. Data ports(USB, RS232 and EPO) were signal port only. no test required. P P N N2.4.1/RD General requirements 2.4.2/RD Limit values Frequency (Hz) .................................... : Measured current (mA) ........................ : Measured voltage (V) .......................... : Measured circuit capacitance (nF or ?F) : 2.4.3/RD Connection of limited current circuits to other circuits 5.2.4 3.5/RD External signaling circuits3.5.1/RD General requirements 3.5.2/RD Types of interconnection circuits ........ : 3.5.3/RD ELV circuits as interconnection circuits 3.5.4/RD Data ports for additional equipment5.2.5 2.5/RDLimited power source a) Inherently limited output b) Impedance limited output c) Regulating network limited output under normal operating and single fault condition d) Overcurrent protective device limited outputP N N P PPage 15 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark VerdictMax. output voltage (V), max. output current (A), max. apparent power (VA) : Current rating of overcurrent protective device (A) .: Use of integrated circuit (IC) current limiters 5.3 5.3.1 2.6/RD Protective earthing and bonding General Provisions for earthing and bonding Appliance coupler and outlets used Relevant earthing conductive parts reliably connected to PE Pin of AC inlet. See below Protective bonding conductors have sufficient current-carrying capacity. Compliance checked. Protective bonding conductors have sufficient current-carrying capacity. Appliance inlet used---P P P P2.6.1/RD Protective earthing2.6.2/RD Functional earthing 2.6.3/RD Protective earthing conductors and protective bonding conductorsP P2.6.3.1/R General DP2.6.3.2/R Size of protective earthing conductors D Rated current (A), cross-sectional area (mm2), AWG ........................................ : 2.6.3.3/R Size of protective bonding conductors D Rated current (A), cross-sectional area (mm2), AWG ........................................ : Protective current rating (A), crosssectional area (mm2), AWG ................. : 2.6.3.4/R Resistance of earthing conductors and D resistance (?), voltage drop (V), test current (A), duration (min) . :P ? PComply with 2.6.3.4/RD Comply with 2.6.3.4/RD (See appended table 5.3)? ? PPage 16 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark Verdict2.6.3.5/R Colour of insulation .............................. : D 2.6.4/RD Terminals 2.6.4.1/R General D 2.6.4.2/R Protective earthing and bonding terminals DYellow-and-GreenP PAC outlet as protective earth terminal. Adequate protective earth connection, see also Subclause 2.6.3.4/RD and 3.3/RD. Comply with 2.6.3.4/RD Separate PE and protective bonding by conductor. See below. This unit has it?s own earthing connection. PE terminals of outlets reliably connected to PE terminal of unit. (AC inlet). Yellow/Green wire terminal of outlet connector to metal chassis There are no switches or overcurrent protective devices in the protective earthing/bonding conductors. AC inlet is considered as possible disconnection. AC input power is cut off before removal of earth pin. Plug, earthing connected before and disconnected after hazardous voltage. No other operator removable parts.P PRated current (A), type, nominal thread diameter (mm) ..................................... : 2.6.4.3/R Separation of the protective earthing D conductor from protective bonding conductors 2.6.5/RD Integrity of protective earthing 2.6.5.1/R Interconnection of equipment D? NP P2.6.5.2/R Components in protective earthing D conductors and protective bonding conductorsP2.6.5.3/R Disconnection of protective earth DP2.6.5.4/R Parts that can be removed by an operator DPPage 17 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark Verdict2.6.5.5/R Parts removed during servicing DProtective earthed parts cannot be removed in a way which impairs safety. No risk of corrosion. Protective bonding conductors connected to metal chassis via ringtype lugs fixed to metal by weld.P2.6.5.6/R Corrosion resistance D 2.6.5.7/R Screws for protective bonding DP N2.6.5.8/R Reliance on telecommunication network or Protective earthing is not D cable distribution system rely on telecommunication network or cable distribtion system. 5.3.2 Protective earthing 2.6.1/RD Reliable connection of relevant conductive parts to the PE terminal (via green/ yellow insulated wires)NP2.10/RD 4.2/RDClearances, creepage distances and distances through insulation Mechanical strength Earthed or unearthed conductive enclosures do not bridge parts between which a hazardous energy level exists and not contact a bare part at hazardous voltage. Refer to 2.6.3.4/RDP P5.2/RD 5.3.3 5.4 5.4.1Electric strength Protective bonding AC and d.c. power isolation General Disconnection from the mains supply considered.P P P PPage 18 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark Verdict3.4/RDDisconnection from the mains supplyDisconnection from the mains supply by plug or appliance coupler. See below. Appliance inlet provided as disconnect device Not a permanently equipment. Adequate protection provided to service personnel during backup mode. None provided. The appliance approved AC inlet disconnected both poles simultaneously. Single-phase equipment. No switches provided. No interconnected equipment EUT is pluggable type and receives power form the AC mains and - in case of AC mains failure - from the built-in batteries. No marking required. Not permanently connected equimentP3.4.1/RD General requirement 3.4.2/RD Disconnect devices 3.4.3/RD Permanently connected equipment 3.4.4/RD Parts which remain energizedP P N P3.4.5/RD Switches in flexible cords 3.4.6/RD Number of poles - single-phase and d.c. equipmentN P3.4.7/RD Number of poles - three-phase equipment 3.4.8/RD Switches as disconnect devices 3.4.9/RD Plugs as disconnect devices 3.4.10/R Interconnected equipment D 3.4.11/R Multiple power sources DN N N N N5.4.2Disconnect devicesP5.5 5.5.1Overcurrent and earth fault protection GeneralP PPage 19 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark Verdict2.7.3/RD Short-circuit backup protectionPluggable equipment type A. Building installation is considered as providing short-circuit backup protection.P2.7.4/RD Number and location of protective devices Over current protector ............................................................ : provided in live conductor (at rear panel). Earth fault protection is considered to be provided in the building for Pluggable A equipment 2.7.5/RD Protection by several devices 2.7.6/RD Warning to service personnel ............. : Only one protection device provided. No double-pole fusing inside this pluggable equipment type A UPS. Stated in the user’s manual. Protection for input is provided by the building for pluggable equipment type A inlet. Pluggable equipment type A outputs provided Ungrounded batteries inside the UPS. For internal battery bank, the protective devices are directly located behind the supply wire of the DC utility. For the charger circuit, two was no hazardous conditions under any simulated fault conditions.PN P5.5.2Basic requirementsP5.5.3 5.5.3.1 5.5.3.2Battery circuit protection Overcurrent and earth fault protection Location of protective deviceP P PPage 20 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark Verdict5.5.3.3Rating of protective deviceProtection against overcurrent by three fuses (parallel) in the plus pole of the battery supply circuit of the UPS. (see appended table 8.3)P5.3.1/RD Protection against overload and abnormal operation 5.5.4 5.5.4.1 5.5.4.2 5.5.4.3 Short-time withstand current General Modes of operation Test procedure Rated UPS output current/(r.m.s) (A) . : Prospective test current/(r.m.s) (A) ..... : Typical power factor ........................... : Initial asymmetric peak current ration (Ipk / Icw) ..................................................... : Minimum durating of prospective test current (cycles 50/60 Hz) .................... : 5.5.4.3.2 Exemption from testing 5.6 5.6.1 2.8/RD Protection of personnel C Safety interlocks Operator protection General principlesP1φ with neutralN N N N N -----P P5.5.4.3.1 General applicationNo safety interlocks. No safety interlocks.N N N N N N N N N N2.8.1/RD Protection requirements 2.8.2/RD Inadvertent reactivation 2.8.3/RD Fail-safe operation 2.8.4/RD Protection against extreme hazard 2.8.5/RD Moving parts 2.8.6/RD Overriding 2.8.7/RD Switches, relays and their related circuits 2.8.7.1/R Separation distances for contact gaps and D their related circuits ............................ :Page 21 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark Verdict2.8.7.2/R Overload test D 2.8.7.3/R Endurance test D 2.8.7.4/R Electric strength test D 2.8.8/RD Mechanical actuators 5.6.2 Service person protection No adjustments or measurements inside the equipment are necessary while the unit is energized. Considered. It is unlikely that during the removal of any covers service personnel may touch hazardous voltage or energy. A risk of injury is unlikely for the service personnel. The UPS is designed with only screwed enclosure parts. No component access during operation mode necessary. No inadvertent reactivation Unintentional contact with the moving parts is not likely. The capacitors provided can produce energy level way below 20 joules.N N N N P5.6.2.1 5.6.2.2Introduction CoversP P5.6.2.3 5.6.2.4Location and guarding of parts Parts on doorsP P5.6.2.5Component accessN2.8.3/RD Fail-safe operation 5.6.2.6 Moving partsN P5.6.2.7Capacitor banksPPage 22 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark Verdict5.6.2.8Internal batteriesThe terminals of the battery connections are isolated and covered so that it is unlikely to bridge the terminals of the battery during servicing or its replacement.P5.7 2.10/RDClearances, creepage distances and distances through insulationP P2.10.1/R General D 2.10.1.1/ Frequency ........................................... : RD 2.10.1.2/ Pollution degrees ................................ : RD 2.10.1.3/ Reduced values for functional insulation RD 2.10.1.4/ Intervening unconnected conductive parts RD 2.10.1.5/ Insulation with varying dimensions RD 2.10.1.6/ Special separation requirements RD 2.10.1.7/ Insulation in circuits generating starting RD pulses 2.10.2/R Determination of working voltage D 2.10.2.1/ General RD 2.10.2.2/ RMS working voltage RD 2.10.2.3/ Peak working voltage RD 2.10.3/R Clearances D Considered Pollution degree 2. The functional insulation complied with clause 5.3.4/RD Considered. No reduction of distances considered. Not special separation requirements. No such circuit generating starting pulses. (See appended table 5.7)P P NP N N NP P P P PPage 23 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark Verdict2.10.3.1/ General RD 2.10.3.2/ Mains transient voltages RD a) AC mains supply ............................ : b) Earthed d.c. mains supplies ........... : c) Unearthed d.c. mains supplies ....... : d) Battery operation ............................ : 2.10.3.3/ Clearances in primary circuits RD 2.10.3.4/ Clearances in secondary circuits RD 2.10.3.5/ Clearances in circuits having starting RD pulses 2.10.3.6/ Transients from a.c. mains supply ...... : RD 2.10.3.7/ Transients from d.c. mains supply ...... : RD 2.10.3.8/ Transients from telecommunication RD networks and cable distribution systems : Normal transient voltage considered. 2500Vpeak Not intended for d.c. mains supplies Not intended for d.c. mains supplies Internal battery considered. (see appended table 5.7) (see appended table 5.7) The circuit will not generating starting pulse. Considered. Not connected to d.c. mains supply. Not connected to telecommunication networks and cable distribution systems Normal transient voltage considered.P P P N N N P P N P N N2.10.3.9/ Measurement of transient voltage levels RD a) Transients from a mains supply For an a.c. mains supply ..................... : For a d.c. mains supply ...................... : b) Transients from a telecommunication network : 2.10.4/R Creepage distances D 2.10.4.1/ General RDN N N N N(see appended table 5.7) Considered.P PPage 24 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark Verdict2.10.4.2/ Material group and comparative tracking RD index CTI tests ............................................. : 2.10.4.3/ Minimum creepage distances RD 2.10.5 /RD Solid insulation Material group IIIb is assumed to be used. (see appended table 5.7) Solid or laminated insulating material having adequate thickness are provided. Considered. (see appended table 5.7) (see appended table 4.5) Optocouplers used. No cemented joint. Thin sheet material in form of polyester tape used in transformer. Tapes used in transformers. 3 layers Not used. Tapes used in transformers. (see appended table 5.7)P P P P2.10.5.1/ General RD 2.10.5.2/ Distances through insulation RD 2.10.5.3/ Insulating compound as solid insulation RD 2.10.5.4/ Semiconductor devices RD 2.10.5.5/ Cemented joints RD 2.10.5.6/ Thin sheet material C General RD 2.10.5.7/ Separable thin sheet material RD Number of layers (pcs) ....................... : 2.10.5.8/ Non-separable thin sheet material RD 2.10.5.9/ Thin sheet material C standard test RD procedure Electric strength test 2.10.5.10 Thin sheet material C alternative test /RD procedure Electric strength test 2.10.5.11 Insulation in wound components /RD 2.10.5.12 Wire in wound components /RDP P P P N PP -N P ? N ?No such components. No such components.N NPage 25 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark VerdictWorking voltage .................................. : a) Basic insulation not under stress .... : b) Basic, supplementary, reinforced insulation ............................................ : c) Compliance with Annex U ............... : Two wires in contact in angle between 45? and 90? : 2.10.5.13 Wire with solvent-based enamel in wound /RD components Electric strength test Routine test 2.10.5.14 Additional insulation in wound components No additional insulation /RD used. Working voltage .................................. : - Basic insulation not under stress ...... : - Supplementary, reinforced insulation : 2.10.6/R Construction of printed boards D 2.10.6.1/ Uncoated printed boards RD 2.10.6.2/ Coated printed boards RD 2.10.6.3/ Insulation between conductors on the RD same inner surface of a printed board See below. Uncoated printed boards used. No such boards used. No such boards used. No wire with solventbased enamel in wound components.? N N N N N? N N ? N N P P N N N --No such construction. N N N2.10.6.4/ Insulation between conductors on different No such boards used. RD layers of a printed board Distance through insulation Number of insulation layers (pcs) ....... : 2.10.7/R Component external terminations D2.10.8/R Tests on coated printed boards and coated No coated printed boards D components and components. 2.10.8.1/ Sample preparation and preliminary RD inspectionPage 26 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark Verdict2.10.8.2/ Thermal conditioning RD 2.10.8.3/ Electric strength test RD 2.10.8.4/ Abrasion resistance test RD 2.10.9/R Thermal cycling D 2.10.10/ RD 2.10.11/ RD Test for Pollution Degree 1 environment and insulating compound Tests for semiconductor devices and cemented joints Approved opto-couplers provided. No other parts to be tested. (see appended table 4.5) No special insulation in order to reduce distance.N ? N N N P2.10.12/ RD 6 6.1 6.1.1 3.1/RDEnclosed and sealed partsNWiring, connections and supply General Introduction General Considered. See below Adequate cross sectional areas on internal wiring. Wire ways are smooth and free from edges. Wires are adequately fixed to prevent excessive strain on wire and terminals and avoiding damage to the insulation of the conductors. Internal wirings is secured against excessive strain, loosening of terminals and damage to the conductor insulation.P P P P P P3.1.1/RD Current rating and overcurrent protection 3.1.2/RD Protection against mechanical damage3.1.3/RD Securing of internal wiringPPage 27 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark Verdict3.1.4/RD Insulation of conductorsInsulation on internal conductors is considered to be of adequate quality and suitable for the application and the working voltage involved. Beads were contained within insulating sleeves and were secured that they could not change their position and create hazards. No screws of insulating material used for electrical connection. All current carrying and safety earthing connections are metal to metal. No self-tapping and spaced thread screws used. Terminations can not become displaced so that clearances and creepage distances can be reduced. Break away or pivot on its terminal is unlikely Sleeves are used as supplementary insulation. The choice of crosssections and ratings of conductors by manufacturer inside the UPS is applicable.P3.1.5/RD Beads and ceramic insulatorsP3.1.6/RD Screws for electrical contact pressureP3.1.7/RD Insulating materials in electrical connectionsP3.1.8/RD Self-tapping and spaced thread screwsN3.1.9/RD Termination of conductorsP10 N pull test 3.1.10/R Sleeving on wiring D 6.1.2 Dimensions and rating of busbars and insulated conductorsP PP6.2 6.2.1Connection to power General provisions for connection to power See below.P PPage 28 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark Verdict3.2.2/RD Multiple supply connections 3.2.3/RD Permanently connected equipmentSingle supply connection. Not an permanently connected equipment. It?s a pluggable equipment type A equipment.N NNumber of conductors, diameter of cable and conduits (mm) .............................. : 3.2.4/RD Appliance inlets 3.2.5/RD Power supply cords 3.2.5.1/R AC power supply cords D Type ................................................... : Rated current (A), cross-sectional area (mm? ), AWG ....................................... : 3.2.5.2/R DC power supply cords D 3.2.6/RD Cord anchorages and strain relief Mass of equipment (kg), pull (N) ........ : Longitudinal displacement (mm) ......... : 3.2.7/RD Protection against mechanical damage No parts under this unit likely to damage the power supply cord. Enclosure without sharp edges. Appliance inlet and outlets used. Not connected to DC power supply. No power supply cord provided Approved appliance inlets used See below-P P P --N N --P3.2.8/RD Cord guards Diameter or minor dimension D (mm); test mass (g) .............................................. : Radius of curvature of cord (mm) ........ : 6.2.2 Means of connection .......................... :N ---Appliance inlet used.PPage 29 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark VerdictMore than one supply connection ....... :Single voltage range supply connection.N6.3 3.3/RDWiring terminals for external power conductors Wiring terminals for connection of external No external power conductors conductor provided Not permanently connected equipment.N N N N N N -N -N N N P3.3.1/RD Wiring terminals 3.3.2/RD Connection of non-detachable power supply cords 3.3.3/RD Screw terminals 3.3.4/RD Conductor sizes to be connected Rated current (A), cord/cable type, crosssectional area (mm2)............................ : 3.3.5/RD Wiring terminal sizes Rated current (A), type, nominal thread diameter (mm) .................................... : 3.3.6/RD Wiring terminal design 3.3.7/RD Grouping of wiring terminals 3.3.8/RD Stranded wire 7 7.1 Physical requirements EnclosureThe frame or chassis not be used to carry current. And provided adequate protection against risk of fire, electric shock, injury to persons and hazardous energy level.P7.2 4.1/RDStability Angle of 10? Test force (N) ...................................... : The unit does not overbalance 55NP P PPage 30 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark Verdict7.3 4.2/RDMechanical strength Tests performed and passed. Results see below. After the tests, unit complied with the requirements of subclauses 2.1.1/RD, 2.6.1/RD, 2.10/RD and 4.4.1/RD. 10 N applied to all components other than enclosure. No such compartments. 250N applied to outer enclosure. No energy or other hazards. No hazard as a result from steel ball impact test. No hazard as a result from steel ball impact test. No hazard as a result from steel sphere ball swung test. No required for this equipment. 70℃, 7hours No cathode ray tube. No high pressure lamp provided. Not for wall or ceiling mounting.P P4.2.1/RD General4.2.2/RD Steady force test, 10 NP4.2.3/RD Steady force test, 30 N 4.2.4/RD Steady force test, 250 NN P4.2.5/RD Impact testPFall testPSwing testP4.2.6/RD D height (mm) ........................ : 4.2.7/RD Stress relief test 4.2.8/RD Cathode ray tubes Picture tube separately certified ......... : 4.2.9/RD High pressure lamps 4.2.10/R Wall or ceili force D (N) ...................................................... : 7.4 7.4.1 Construction details IntroductionN P N ? N NP PPage 31 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark Verdict4.3.1/RD Edges and corners 4.3.2/RD Handles force (N): 4.3.3/RD Adjustable controls 4.3.4/RD Securing of partsEdges and corners of the enclosure are rounded. No adjustable controls. Mechanical fixings in such a way designed that they will withstand mechanical stress occurring in normal use. No mismatch of connectors. No heating elements provided. No containers for liquid or gases in the equipment DC fan, test finger applied to openings. No fan blade accessible. No service access areas No service access areas No service access areas No service access areasP P N P4.3.5/RD Connection by plugs and sockets 4.3.7/RD Heating elements in earthed equipment 4.3.11/R Containers for liquids or gases D 4.4/RDP N NProtection against hazardous moving parts No such parts.P P4.4.1/RD General4.4.2/RD Protection in operator access areas ... : 4.4.3/RD Protection in restricted access locations : 4.4.4/RD Protection in service access areas 4.4.5/RD Protection against moving fan blades 4.4.5.1/R General D Not considered to cause pain or injury. a) ............................................................ : Is considered to cause pain, not injury. b) ............................................................ : Considered to cause injury. c) ............................................................ : 4.4.5.2 Protection for usersP P P P P N N PProtection against moving fan blades by metal enclosurePUse of symbol or warning ................... :NPage 32 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark Verdict4.4.5.3Protection for service personsProtection against moving fan blades by metal enclosurePUse of symbol or warning ................... : 4.5/RD Thermal requirements See below. (See appended table 7.7) See Annex L (see appended table 7.7) (see appended table 7.7) (see appended table 7.7) Suitable construction prevent vertical access to bare parts of hazardous voltage. (see appended table 7.4.2) For the ventilation of the lead-acid battery refer to table M No castors provided. 4.5.1/RD General 4.5.2/RD Temperature tests Normal load condition per Annex L ..... : 4.5.3/RD Temperature limits for materials 4.5.4/RD Touch temperature limits 4.5.5/RD Resistance to abnormal heat .............. : 7.4.2 OpeningsN P P P -P P P P7.4.3Gas ConcentrationP7.4.4 7.5 4.7/RDEquipment movement Resistance to fireN P P P4.7.1/RD Reducing the risk of ignition and spread of See below. flame Method 1, selection and application of components wiring and materials Use of materials with the required flammability classes. (see appended table 7.5)Method 2, application of all of simulated fault condition tests 4.7.2/RD Conditions for a fire enclosure 4.7.2.1/R Parts requiring a fire enclosure D See below. Internal components required a fire enclosure.N P PPage 33 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark Verdict4.7.2.2/R Parts not requiring a fire enclosure D 4.7.3/RD Materials 4.7.3.1/R General DThe fire enclosure is required to cover all parts. See below. Components and materials have adequate flammability classification. V-1 or better No parts outside the fire enclosure. Internal components except small parts are minimum V-2 material. Batteries have a flammability class of HB or better. No air filters in the equipment.NP P4.7.3.2/R Materials for fire enclosures D 4.7.3.3/R Materials for components and other parts D outside fire enclosures 4.7.3.4/R Materials for components and other parts D inside fire enclosuresP N P4.7.3.5/R Materials for air filter assemblies DN N4.7.3.6/R Materials used in high-voltage components No parts exceeding 4kV. D 7.6 7.6.1 Battery location Battery location and installation Maintenance free batteries used inside the UPS. The batteries are connected by quick connect terminals (no necessary tightening). No requirements declared by the battery manufacturer. The temperature of the electrolyte and the gas emission are within the limits of this standard (see appropriate subclauses).P P7.6.2Accessibility and maintainabilityP7.6.3DistancePPage 34 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark Verdict7.6.4 7.6.5Case insulation WiringNo Ni-Cd battery used inside. The protection of connection wiring complies with subclause 3/RD. Sealed maintenance free batteries provided with an unlikely emission of electrolyte (VRLA type). For the ventilation of the lead-acid battery refer to table M. Protected against excessive voltages under normal and single fault conditions.P P7.6.6Electrolyte spillageP7.6.7VentilationP7.6.8Charging voltageP7.7 4.5/RDTemperature rise Thermal requirements (see appended table 7.7) (see appended table 7.7) (see appended table 7.7) (see appended table 7.7)P P P P -P P P P P (see appended table 8) The touch current does not exceed 3.5mA. P N4.5.1/RD General 4.5.2/RD Temperature tests Normal load condition per Annex L ..... : 4.5.3/RD Temperature limits for materials 4.5.4/RD Touch temperature limits 4.5.5/RD Resistance to abnormal heat .............. : 8 8.1Electrical requirements and simulated abnormal conditions General provisions for earth leakage5.1.1/RD General 5.1.7/RD Equipment with touch current exceeding 3,5 mA 8.2 5.2/RD Electric strengthP (see appended table 5.7) P5.2.1/RD GeneralPage 35 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark Verdict5.2.2/RD Test procedure 8.3 8.3.1 Abnormal operating and fault conditions General(see appended table 5.7)P P P5.3.1/RD Protection against overload and abnormal operation 5.3.2/RD Motors 5.3.3/RD Transformers 5.3.4/RD Functional insulation ............................ : 5.3.5/RD Electromechanical components(see appended table 8.3) (see appended Annex B/RD) (see appended Annex C/RD) By short-circuit No such electromechanical components that will cause hazardP P P P N5.3.9/RD Compliance criteria for abnormal operating See below and fault conditions 5.3.9.1/R During the tests D No fire or molten metal occurred and no deformation of enclosure during the tests. No reduction of clearance and creepage distances. Electric strength test is made on functional, basic and reinforced insulation. (see appended table 8.3) The equipment was tested under normal use and foreseeable misuse conditions.P P5.3.9.2/R After the tests DP8.3.2 8.3.3Simulation of faults Conditions for testsP P9 6/RD 6.1/RDConnection to telecommunication networks Protection of telecommunication network service persons, and users of other equipment connected to the network, from hazards in the equipmentN NPage 36 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark Verdict6.1.1/RD Protection from hazardous voltages 6.1.2/RD Separation of the telecommunication network from earth 6.1.2.1/R Requirements D Supply voltage (V) .............................. : Current in the test circuit (mA) .......... : 6.1.2.2/R Exclusions .......................................... : D 6.2/RD Protection of equipment users from overvoltages on telecommunication networks 1.5kV No telecommunication network circuitsN N N ? ? N N N N N N N N -N N N N N N N -N N NPage 37 of 736.2.1/RD Separation requirements 6.2.2/RD Electric strength test procedure 6.2.2.1/R Impulse test D 6.2.2.2/R Steady-state test D 6.2.2.3/R Compliance criteria D 6.3/RD Protection of the telecommunication wiring system from overheating Max. output current (A) ....................... : 3.5/RD Interconnection of equipment 3.5.1/RD General requirements 3.5.2/RD Types of interconnection circuits ........ : 3.5.3/RD ELV circuits as interconnection circuits 3.5.4/RD Data ports for additional equipment 2.1.3/RD Protection in restricted access locations 2.3.1/RD Limits Type of TNV circuits ............................ : 2.3.2/RD Separation from other circuits and from accessible parts 2.3.2.1/R General requirements D 2.3.2.2/R Protection by basic insulation DDongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark Verdict2.3.2.3/R Protection by earthing D 2.3.2.4/R Protection by other constructions ....... : D 2.3.3/RD Separation from hazardous voltages Insulation employed ............................. : 2.3.4/RD Connection of TNV circuits to other circuits Insulation employed ............................. : 2.3.5/RD Test for operating voltages generated externally 2.6.5.8/R Reliance on telecommunication network or Protective earthing does D cable distribution system not rely on a telecommunication network or a cable distribution system. 2.10.3.3/ Clearances in primary circuits RD 2.10.3.4/ Clearances in secondary circuits RD 2.10.4/R Creepage distances D 2.10.4.1/ General RD 2.10.4.2/ Material group and comparative tracking RD index CTI tests .............................................. : 2.10.4.3/ Minimum creepage distances RD M/RD M.1/RD M.2 /RD M.3/RD M.3.1.1/ RD Annex M, CRITERIA FOR TELEPHONE RINGING SIGNALS (see 2.3.1/RD) Introduction Method A Method B Frequency (Hz) ................................... : Considered.N N N -N -N NN N N N N ? NN N N N N -Page 38 of 73M.3.1/RD Ringing signalDongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark VerdictM.3.1.2/ RD M.3.1.3/ RD M.3.1.4/ RD M.3.2.1/ RD M.3.2.2/ RD M.3.2.3/ RD A/RD A.1/RDVoltage (V) .......................................... : C time (s), voltage (V) ............ : Single fault current (mA) ..................... :---N -N NM.3.2/RD Tripping device and monitoring voltage . : Conditions for use of a tripping device or a monitoring voltage Tripping device Monitoring voltage (V) ........................ :Annex A, Tests for resistance to heat and fire Flammability test for fire enclosures of movable equipment having a total mass exceeding 18 kg, and of stationary equipment (see 4.7.3.2/RD) Wall thickness (mm) ............................ :N NA.1.1/RD Samples............................................... : A.1.2/RD Con temperature (?C) ......... : A.1.3/RD Mounting of samples .......................... : A.1.4/RD Test flame (see IEC ) Flame A, B, C or D ............................. : A.1.5/RD Test procedure A.1.6/RD Compliance criteria Sample 1 burning time (s).................... : Sample 2 burning time (s).................... : Sample 3 burning time (s).................... : A.2/RD Flammability test for fire enclosures of movable equipment having a total mass not exceeding 18 kg, and for material and components located inside fire enclosures (see 4.7.3.2/RD and 4.7.3.4/RD) Wall thickness (mm) ............................ : A.2.2/RD Con temperature (° C) ......... :--N N N -N N ---NA.2.1/RD Samples, material ................................ :--NPage 39 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark VerdictA.2.3/RD Mounting of samples .......................... : A.2.4/RD Test flame (see IEC ) Flame A, B or C .................................. : A.2.5/RD Test procedure A.2.6/RD Compliance criteria Sample 1 burning time (s).................... : Sample 2 burning time (s).................... : Sample 3 burning time (s).................... : A.2.7/RD Alternative test acc. to IEC , cl. 5 and 9 Sample 1 burning time (s).................... : Sample 2 burning time (s).................... : Sample 3 burning time (s).................... : A.3/RD Hot flaming oil test (see 4.6.2/RD) A.3.1/RD Mounting of samples A.3.2/RD Test procedure A.3.3/RD Compliance criterion B/RD B.1/RD Annex B, Motor tests under abnormal conditions (see 4.7.2.2/RD and 5.3.2/RD) General requirements Position ............................................... : Manufacturer ...................................... : Type ................................................... : Rated values ...................................... : B.2/RD B.3/RD B.4/RD B.5/RD Test conditions Maximum temperatures Running overload test Locked-rotor overload test Test duration (days) ............................ : Electric strength test: test voltage (V) . : B.6/RD Running overload test for d.c. motors in secondary circuits Enclosure Inside (see appended table 4.5) (see appended table 4.5) (see appended table 4.5)N N -N N ---N ---N N N N P P ----N N N N --NPage 40 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark VerdictB.6.1/RD General B.6.2/RD Test procedure B.6.3/RD Alternative test procedure B.6.4/RD El test voltage (V) . : B.7/RD Locked-rotor overload test for d.c. motors in secondary circuitsN N N N N N N N N N N N -P ? ? ? ? ? P (see appended table C.2/RD) By insulation tapes P P P P NB.7.1/RD General B.7.2/RD Test procedure B.7.3/RD Alternative test procedure B.7.4/RD El test voltage (V) . : B.8/RD B.9/RD Test for motors with capacitors Test for three-phase motors Operating voltage (V) ......................... : C/RD Annex C, Transformers (see 1.5.4/RD and 5.3.3/RD) Position ............................................... : Manufacturer ...................................... : Type ................................................... : Rated values ...................................... : Method of protection ............................ : C.1/RD C.2/RD Overload test Insulation Protection from displacement of windings: D/RD D.1/RD D.2/RD TX1 (See appended table 4.5) (See appended table 4.5) (See appended table 4.5) By protection circuitsB.10/RD Test for series motorsAnnex D, Measuring instruments for touch current tests (see 5.1.4/RD) Measuring instrument Alternative measuring instrument As in figure D.1 used. Not used.Page 41 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark VerdictE/RD F/RDAnnex E, Temperature rise of a winding (see Annex E/RD) Annex F, Measurements of clearances and creepage distance (see 2.10/RD and Annex G/RD) Annex G, Alternative method for determining minimum clearances ClearancesN PG/RD G.1/RDN N N N N N N N N N N N N N N N N N N N N NG.1.1/RD General G.1.2/RD Summary of the procedure for determining minimum clearances G.2/RD Determination of mains transient voltage (V) G.2.1/RD AC mains supply ................................. : G.2.2/RD Earthed d.c. mains supplies ................ : G.2.3/RD Unearthed d.c. mains supplies ........... : G.2.4/RD Battery operation ................................ : G.3/RD G.4/RD Determination of telecommunication network transient voltage (V) .............. : Determination of required withstand voltage (V)G.4.1/RD Mains transients and internal repetitive peaks .................................................. : G.4.2/RD Transients from telecommunication networks ............................................. : G.4.3/RD Combination of transients G.4.4/RD Transients from cable distribution systems G.5/RD Measurement of transient voltages (V) a) Transients from a mains supply For an a.c. mains supply For a d.c. mains supply b) Transients from a telecommunication network G.6/RD H Determination of minimum clearances : Annex H, Guidance on protection against ingress of water and foreign objects (see IEC 60529)Page 42 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark VerdictI I.1 I.2Annex I, Backfeed protection test General Test for pluggable UPSBackfeed relay provided,P P Test P for single-phase equipment.I.3 I.4 I.5Test for permanently connected UPS Load-induced change of reference potential Solid-state backfeed protection (see clause 7.1-7.5 of IEC 62040-2 and clause 7.1-7.2 of IEC 62040-3) Annex J, Table of electrochemical potentials (see 2.6.5.6/RD) Metal(s) used ...................................... : Metals which the combination electrochemical potential is less than 0.6V. (See appended table 5.1.4)N P NJ/RDP ?K/RD K.1/RD K.2 /RD K.3/RD K.4/RD K.5/RD K.6/RD L L.1Annex K, Thermal controls (see 1.5.3/RD and 5.3.8/RD) Making and breaking capacity Th operating voltage (V) ............................................................ : Therm operating voltage (V) .......................................... : Temperatu operating voltage (V) .......................................... : Thermal cut-out reliability Stability of operation Annex L, Reference loads General Worst case loads specified by the manufacturer maintained during the relevant tests.N N N N N N N P PL.2 L.3Reference resistive load Reference inductive-resistive loadN -Page 43 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark VerdictL.4 L.5 L.5.1 L.5.2 L.5.3Reference capacitive-resistive loads Reference non-linear load General Test method Connection of the non-linear reference load Worst case power factors as specified by the manufacturer maintained during the relevant tests.P N N N --M M.1M.2 M.3 M.4 NAnnex M, Ventilation of battery compartments Sufficient openings and a General suitable arrangement of components (circuit breaker) are provided in such a way that a local concentration of hydrogen and oxygen is not possible. No requirement regarding the separation of operational arcing parts from battery vents/valves. See appended table M Normal conditions Blocked conditions Overcharge conditions Block test applied, see appended table 8.3 See appended table M.P PP P P NAnnex N, Minimum and maximum cross-sections of copper conductors suitable for connection (see 6.3) Annex U, Insulated winding wires for use without interleaved insulation (see 2.10.5.4/RD)U/RDN? V/RD V.1/RD V.2/RD V.3/RD Annex V, AC POWER DISTRIBUTION SYSTEMS (see 1.6.1/RD) Introduction TN power distribution systems TT power distribution systems See below. See sub-clause 1.6.1/RD. P P P NPage 44 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SIEC 62040-1 Clause Requirement + Test Result - Remark VerdictV.4/RDIT power distribution systemsNPage 45 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638S4.5TABLE: Critical components information Technical data StandardP Mark(s) of conformit y1)UL MH28204 UL MH28269Object / part Manufacturer/ Type / No. trademark model- Description: Battery (Alternative)Whole unit YUASA SHIMASTU ELECTRONIC TECHNOLOGY LTD SHENZHEN CENTER POWER TECHNOLOGY CO LTD SHENZHEN LEOCH BATTERIES TECHNOLOGY CO LTD CSB CSB SHENZHEN RITAR POWER CO LTD RONGFENG TECX-UNIONS Technology Corporation Rich Bay Co., Ltd. VOLTRONIC POWER TECHNOLOGY (SHENZHEN) CORP. KUOYUH W.L. ENTERPRISE CO.,LTD NPW45-12 NP 9.0-12 12V, 45W/Cell, HB UL1989 12 V, 9AH, HB UL1989(Alternative)CP120812 V, 9AH, HBUL1989UL MH25860(Alternative)DJW12-1012 V, 9AH, HBUL1989UL MH26866(Alternative) (Alternative) (Alternative) Appliance inlet (Alternative)HR 1234W12V, 34W, HBUL1989 UL1989 UL1989GP V 28W RT1290 12 V, 9AH, HBUL MH14533 UL MH14533 UL MH28539 VDE TUVSS-3B TU-320-WAC250V, 16A AC250V, 16AEN60320-1 EN60320-1(Alternative) Appliance outletR-305SN2 REC HXH/GE2PAC250V, 16A AC250V, 16AEN60320-1 EN60320-1VDE Test in applianceInput Breaker8816A/250VACEN 60934EnclosureLG CHEMICAL LTD CHIMEI(Alternative)AF310, AF310HT, AF312C PA765A PA757A AF310, AF310HT, AF312CSwitch knobLG CHEMICAL LTDV-0, 80℃, Min. thickness 2.5mm V-0, 80℃, Min. thickness 2.5mm V-0, 80℃, Min. thickness 2.5mmUL94TUV Certificate No. B3 UL E67171UL94UL E56070UL94UL E67171Page 46 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638S(Alternative)CHIMEIPA765A PA757A VariousHeatshrinkable tube - Description: Inverter IGBT (Q7, Q8, Q13, Q14) PFC IGBT Converter MOSFETs PCB EnclosureVariousV-0, 80℃, Min. thickness 2.5mm 600, 125℃UL94UL E56070UL 224ULMain board APEC AP30G120AS 1200V, 30A W IGW30N100T 1000V,30A IRF3710 Various AF310, AF310HT, AF312C PA765A PA757A AF310, AF310HT, AF312C PA765A PA757A 65NM-300H 100V, 57A V-0, 130℃ V-0, 80℃, Min. thickness 2.5mm V-0, 80℃, Min. thickness 2.5mm V-0, 80℃, Min. thickness 2.5mm V-0, 80℃, Min. thickness 2.5mm 125Vdc, 30A IEC 60950-1 Tested in equipment Tested in equipment Tested in equipment UL UL E67171infineon IR Various LG CHEMICAL LTD CHIMEIIEC 60950-1 IEC 60950-1 UL 796 UL94(Alternative)UL94UL E56070Switch knobLG CHEMICAL LTD CHIMEIUL94UL E67171(Alternative)UL94UL E56070Battery fuse (F2, F3 for model 3KVA) (Alternative) Battery fuse (F2, F3 for model 2KVA) (Alternative) Input fuse (F1)HOLLYFUSEUL 275UL E156471BUSSMANN HOLLYFUSEABC-30-R 65NM-200H125Vdc, 30A 125Vdc,20AUL 275 UL 275UL E19180 UL E156471BUSSMANN HOLLYFUSE(Alternative) BUSSMANN Fuse on charger HOLLYFUSE (Alternative) Fuse on super charger (Alternative) Input breaker SUN FUSE HOLLYFUSEABC-20-R 65NM(P)200H ABC-V-20-R 42NM(P)030H2 5RP-G 50F-063H125Vdc,20A 250Vac,20A 250Vac,20A 250Vac,2A 250Vac,2A 250Vac,6.3AUL 275 UL 248 UL 248 UL 248 UL 248 UL 248UL E19180 UL E156471 UL E19180 UL E156471 UL E166522 UL E156471, VDE UL E19180 VDE UL E155159BUSSMANN KUOYUH W L ENTERPRISE CO LTD RONG FENG INDUSTRIAL CO LTD YEU SHENG ELECTRIC CO TOPSTONES500-6.3-R250Vac,6.3A88-16-P1B14- AC250V, 16A P0W RFMB AC250V, 16AEN60127-1 EN60127-2 EN 60934(Alternative)EN 60934UL E142783(Alternative)MBAC250V, 15AEN 60934(Alternative)L AC250V, 16AEN 60934UL E209138, TUV TUVPage 47 of 73Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638SInput Relay (RY1) (Alternative)Output relay (RY2) (Alternative)Converter transformer TX2 (Alternative)(Alternative) (Alternative)Choke (L6)(Alternative)(Alternative) (Alternative)Choke (L7)(Alternative)(Alternative) (Alternative)Choke (L9)(Alternative)(Alternative) (Alternative)CTSong Chuan Precision Co., Ltd XIAMEN HONGFA ELECTROACOU STIC CO LTD Song Chuan Precision Co., Ltd XIAMEN HONGFA ELECTROACOU STIC CO LTD Click technology(shen zhen) CO.LTD MYLAR ELECTRONICS CO.,LTD. ZHUHAI LION CO.,LTD RongChyuan Technology Corporation Click technology(shen zhen) CO.LTD MYLAR ELECTRONICS CO.,LTD. ZHUHAI LION CO.,LTD RongChyuan Technology Corporation Click technology(shen zhen) CO.LTD MYLAR ELECTRONICS CO.,LTD. ZHUHAI LION CO.,LTD RongChyuan Technology Corporation Click technology(shen zhen) CO.LTD MYLAR ELECTRONICS CO.,LTD. ZHUHAI LION CO.,LTD RongChyuan Technology Corporation Click841-P-2A-C-H 12VDC, 25A/220VAC HF116F12VDC, 1/012DA25A/220VAC 2HTFW 793-P-1C-F 6VDC 16A/240VAC 1C; HF14FW/006- 6VDC ZTF 16A/240VAC 1C; 41-----------------020002-EN 61810 EN 61810T?V, UL E88991 UL E134517 TUV R T?V, UL E88991 UL E134517, VDE Tested in equipment Tested in equipment Tested in equipment Tested in equipment Tested in equipment Tested in equipment Tested in equipment Tested in equipment Tested in equipment Tested in equipment Tested in equipment Tested in equipment Tested in equipment Tested in equipment Tested in equipment Tested in equipment Tested inPage 48 of 73EN 61810 EN 61810Class B Class BIEC 60950-1 IEC 60950-1Class B Class BIEC 60950-1 IEC 60950-1130℃ 130℃ 130℃ Class BIEC 60950-1IEC 60950-1IEC 60950-1 IEC 60950-1130℃ 130℃ 130℃ Class BIEC 60950-1IEC 60950-1IEC 60950-1 IEC 60950-1130℃ 130℃ 130℃ Class BIEC 60950-1IEC 60950-1IEC 60950-1 IEC 60950-1Class BIEC 60950-1Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1512638Stransformer (CT3) (Alternative)(Alternative) (Alternative)X2 Capacitor (C3) (Alternative)technology(shen zhen) CO.LTD MYLAR ELECTRONICS CO.,LTD. ZHUHAI LION CO.,LTD RongChyuan Technology Corporation Farad Electronics Co. Ltd Winday00G 41---G PXK MPX Class B IEC 60950-1equipment Tested in equipment Tested in equipment Tested in equipmentClass B Class BIEC 60950-1 IEC 60950-1AC275V, 2.2uF(Alternative)JinghaoCBB62B(Alternative)FaratronicMKP62(Alternative)EpcosB3292#Y2 Capacitor (C5) (Alternative)Taishan City JA Juhong Electronic Ltd. JYA-NAY Co., JR Ltd. Walsin AC Technology Corp. Jyh Chung JY Electronic Co., Ltd. Taishan City JA Juhong Electronic Ltd. JYA-NAY Co., JR Ltd. Walsin AC Techn